E-mail: [email protected]
21 · 2 · Aufhauser Nickel Brazing Alloys Ideal for brazing nickel super alloys
contactBNi-2 is the AWS designation for this material. N99620 is the UNS number. It has a moderately low tensile strength among the nickel-based brazing fillers in the database.
contact20201016 · AMS 4777 (BNI-2) Safety Data Sheet according to the Hazardous Products Regulation (February 11, 2015) Date of issue: 29 November 2017 Version: 2.0
contact202051 · Fig. 1 shows the micrograph and EDS maps of the interfacial zone in the Mo/316L joint brazed with BNi-2 paste. It can be seen from Fig. 1 a that two diffusion zones (DZ1 close to Mo and DZ2 close to 316L) are developed due to the inter-diffusions between the filler layer and base materials. The formation of diffusion zone implied favorable
contactExisting works of literature have reported on the welding of Inconel alloys with expensive filler/interlayers such as MBF or BNi-2 interlayer [20][21][22] [23] [24] but the clarification on the ...
contact2019415 · The results for BFM #36 (36Pd, 48.7Ni, 11Cr, 2.2Si, 2.1B) were referred to alloy BNi-2. In the test, a better result was obtained for the alloy containing Pd, which unlike in the BNi group BFM, evenly spreads
contact2019112 · In this research, microstructure and intermetallic components of IN 718/BNi-2/316 L joint were studied. Dissimilar bonding was carried out at a temperature of 1050 °C and, bonding time varied at 30 and 45 min in a vacuum furnace under an approximate pressure of 10−5 mbar. After TLP joining, samples were analyzed by energy
contact2012121 · At an optimized brazing condition, various filler metals were used. Microstructures were observed at each condition. Filler metals were titanium based 40Ti–20Zr–20Cu–20Ni, silver based Ag–5Pd, and nickel based Ni–7Cr–3.1B–4.5Si–3Fe–0.06C (BNi 2) and Ni–14Cr–10P–0.06C (BNi 7). To select a
contactBNi-2 is the AWS designation for this material. N99620 is the UNS number. It has a moderately low tensile strength among the nickel-based brazing fillers in the database. The graph bars on the material properties cards below compare AWS BNi-2 to: nickel-based brazing fillers (top), all nickel alloys (middle), and the entire database (bottom).
contact2013211 · less steel joints brazed with BNi-2, BNi-5 and BNi-7 underwent heat treatment. The joints were first brazed at standard brazing temperatures for the three filler metals, i.e., 1040°C (1904°F) for BNi-2, 1190°C (2174°F) for BNi-5, and 1065°C (1949°F) for BNi-7. Heat treatment was then carrie d out at 1000°C (1832°F) and
contactAMS 4777 is a nickel-chromium-silicon-boron-iron brazing alloy powder with low joining temperature. It provides high temperature joint strength plus oxidation, corrosion, and abrasion resistance on thick sections of stainless steel, ductile nickel, and cobalt base alloys. Typical applications would include structural members in jet engines ...
contact202051 · Fig. 1 shows the micrograph and EDS maps of the interfacial zone in the Mo/316L joint brazed with BNi-2 paste. It can be seen from Fig. 1 a that two diffusion zones (DZ1 close to Mo and DZ2 close to 316L) are developed due to the inter-diffusions between the filler layer and base materials. The formation of diffusion zone implied favorable
contact2012121 · At an optimized brazing condition, various filler metals were used. Microstructures were observed at each condition. Filler metals were titanium based 40Ti–20Zr–20Cu–20Ni, silver based Ag–5Pd, and nickel based Ni–7Cr–3.1B–4.5Si–3Fe–0.06C (BNi 2) and Ni–14Cr–10P–0.06C (BNi 7). To select a
contact202148 · C/C composite was brazed to TiAl intermetallic compound using a commercial BNi-2 brazing filler metal under vacuum brazing condition. The brazing temperature was 1030~1150 °C and the holding time was 20 min. The joint interfacial microstructures and mechanical properties were studied, and the fracture behavior and
contact2018123 · Data Sheet Icronibsi - 7 (AMS 4777, BNi-2) Morgan Advanced Materials, 2425 Whipple Road, Hayward CA 94544 Contact: +1 510 491 1100 | Certifications: AS9100D, ISO9001:2015, ISO14001:2015
contact2013211 · less steel joints brazed with BNi-2, BNi-5 and BNi-7 underwent heat treatment. The joints were first brazed at standard brazing temperatures for the three filler metals, i.e., 1040°C (1904°F) for BNi-2, 1190°C (2174°F) for BNi-5, and 1065°C (1949°F) for BNi-7. Heat treatment was then carrie d out at 1000°C (1832°F) and
contactにして,BNi-2を いたの1323K びNi-Si-Bを いたの1333Kの をき, するをし た.BNi-2を いたの1323K びNi-Si-Bを い たの1333Kに おけるせんは,ろ うの にし, なはさなかった. 3.2ろ うの
contact2015323 · † BNi-8 is also used in honeycomb brazements and on stainless steels and other corrosion-resistant base metals. † BNi-9 is excellent for jet engine parts Table 2 — Material Costs of Brazing Alloys Based on Their Gold, Silver, and Nickel Content Brazing Filler $/in.2 $/ft2 at 0.001-in. at 0.001-in. joint joint clearance clearance AWS BAu-1 ...
contactBNi-2 is a widely used nickel-based brazing filler. It has low melting temperature, good wettability and fluidity. During the brazing process, the grains of the base metal will not grow up and will not affect the performance of components. decreased, the brazed joint has high high temperature strength and good oxidation resistance. Send Inquiry.
contactBNI-2 AMS4777 amporhous brazing foil filler metal alloy, US $ 5 - 300 / Kilogram, Anhui, China, HUAZHONG, HZ-BNi-2.Source from Anhui Huazhong Welding Industry Co., Ltd. on .
contact2018920 · Both AWS BNi-2 and AWS BNi-5 are nickel alloys. Both are furnished in the as-fabricated (no temper or treatment) condition. They have 82% of their average alloy composition in common. For each property being compared, the top bar is AWS BNi-2 and the bottom bar is AWS BNi-5. AWS BNi-2 (N99620) Filler Metal AWS BNi-5 (N99650)
contactAWS A5.8 BNi-2 AMS4777 B50TF204 PWA1183 MSRR9500/97 EMS56610 EMS54752 Type II EMS94777 DMR35.302 PMI1092 MS1063 CD1068 CUK01-091 ... steels, thin materials, heat exchangers, honeycomb; lower melting temperature general purpose alloy: NI78: AWS A5.8 BNi-3 AMS4778 B50TF205 MSRR9500/114 EMS56600 EMS54752
contact2016928 · Page 1 of 2 The Prince & Izant Company 12999 Plaza Drive Cleveland, Ohio 44130 T: 216-362-7000 F: 216-362-7456 AMS 4777 (BNi-2) T E C H N I C A L D A T A NOMINAL COMPOSITION Nickel Chromium Boron Silicon Iron Phosphorus Carbon Sulfur Titanium Aluminum Zirconium Cobalt Selenium Other
contactBNi-9 is a eutectic nickel-based brazing alloy suitable for brazing nickel, super alloys, stainless steels and other assemblies which require good joint strength at high temperatures with excellent corrosion and xidation resistance. Some of the applications for this filler metal are highly stressed sheet metal components, jet engine parts, and ...
contact2013125 · tween the Alloy 600 and steel, as shown in Fig. 1. Brazing was done in an elec tric resistance heated furnace in an argon gas atmosphere. Brazing temperatures were 50°, 100°, and 1 50°C (90°, 180° and 270°F) above the liquidus temperature of each braz ing foil. In the case of BNi-2, the liq uidus temperature was 1000°C (1832°F);
contactThe world's largest business referral organization is just a few clicks away. Find a business networking chapter near you to get started.
contact