E-mail: [email protected]
2020218 · The machined surface integrity has significance on fatigue life. The step-by-step feed cutting is put forward and adopted to machine ZL109 aluminum-silicon
contact2020110 · Dry wear characteristics of ZL109 aluminum silicon alloy for engine piston under unidirectional and reciprocating rolling-contact friction were studied comparatively.
contactof the machined ZL109 aluminum-silicon alloy sur-face in order to improve the piston surface wear resistance. Reciprocating rotation consists of unidirectional rolling in two-direction.
contact2022420 · This work characterizes the microstructure and investigates the mechanical and wear-resistance properties of plasma-sprayed Ni60CuMo coatings
contact202031 · It can improve the machined quality of ZL109 aluminum-silicon piston alloy and the fatigue life when the reasonable cutting parameter is adopted. Those results
contactThe step-by-step feed cutting is put forward and adopted to machine ZL109 aluminum-silicon piston alloy. In addition, the forward and reverse finish cutting is also proposed to
contactZL109 aluminum alloy has good mechanical properties at high temperature, which is a material for piston manufacturing. However, cutting of ZL109 aluminum alloy leads to serious tool wear and it is difficult to obtain better machining accuracy. For cutting simulation using ABAQUS software, it is necessary to obtain the material parameters. J-C constitutive
contact202031 · It can improve the machined quality of ZL109 aluminum-silicon piston alloy and the fatigue life when the reasonable cutting parameter is adopted. Those results have an important practical ...
contactThe step-by-step feed cutting is put forward and adopted to machine ZL109 aluminum-silicon piston alloy. In addition, the forward and reverse finish cutting is also proposed to improve the ...
contact2022630 · ZL109 aluminum alloy has an excellent casting and airtight performance, low linear expansion coefficient and density, is widely used in the internal combustion engine piston and other parts 2.
contact20161215 · Effects of Serpentine Nano-particles on the Friction Properties of Miro-arc Oxidation Films Produced on ZL109 Aluminum Alloy Piston Surface HU Haifeng, LIU Xinjian, WANG Lianhai, LI Xiao, CHEN Qunsheng
contact2020826 · . ： JIS ISO GB YB HB ГOCT ASTM UNS ANSI AA SAE BS BS/L NF AIRLA DIN ZL101 ZL11 HZL101 AЛ9，AЛ9B A03560 A13560 356.0 A356.0 323 A-S7G AS7G03 GAlSi7Mg (3.2371.61... :YB－，HB－、。.
contact2006114 · Abstract：Grades of aluminium alloy in common use at home and abroad and relevant informations were summarized． ... ZL109 ZL110 G ZL11l ZL114A ZL201 ZL203 ZL301 ZL402 Y102 Y104 Yl12 Yl13
contactZL109 aluminum alloy has good mechanical properties at high temperature, which is a material for piston manufacturing. However, cutting of ZL109 aluminum alloy leads to serious tool wear and it is difficult to obtain better machining accuracy. For cutting simulation using ABAQUS software, it is necessary to obtain the material parameters. J-C constitutive
contact2020826 · . ： JIS ISO GB YB HB ГOCT ASTM UNS ANSI AA SAE BS BS/L NF AIRLA DIN ZL101 ZL11 HZL101 AЛ9，AЛ9B A03560 A13560 356.0 A356.0 323 A-S7G AS7G03 GAlSi7Mg (3.2371.61... :YB－，HB－、。.
contact2006114 · Abstract：Grades of aluminium alloy in common use at home and abroad and relevant informations were summarized． ... ZL109 ZL110 G ZL11l ZL114A ZL201 ZL203 ZL301 ZL402 Y102 Y104 Yl12 Yl13
contact2022111 · The ZL109 aluminum alloy with the dimensions of 15 × 15 × 10 mm was used as the substrate. Prior to spraying, the specimen was sandblasted to obtain a clean and highly active surface. Then the sample was ultrasonically cleaned with ethanol and acetone.In this paper, the plasma spray equipment independently developed by the
contact20131020 · OUYANG Liuzhang,LUO Chengping, LUO Zhuoxuan, SUI Xiandong, Study on Interface Characteristics of SiCp/ZL109 Aluminium Alloy Composites, Foundry, 3, 9(1999) 8 (, , , , SiCp/ZL109,
contact20151018 · 2.It was studied that the technology conditions of microarc oxidation of ZL109 higher-silicon cast aluminium alloys and the structure, the micrograph of surface, the conditions of microarc oxidation ceramic coating.ZL109
contact2019710 · During the machining process of aluminum alloy containing high-hardness silicon particles, it is prone to produce the built-up edge, tool-chip coherence and serious tool wear, which makes it difficult to obtain a good surface quality. Therefore, optimizing the cutting parameters of Al-Si alloy ZL109 for
contact2019927 · Their results showed that the creep resistance was higher, when the air-cooling condition was used. It was gradually decreased, when the solution time enhanced. Zhang et al modelled tensile and compressive creep behaviors of the ZL109 aluminum alloy. They indicated that the stress and the temperature affected asymmetric mechanisms.
contact2019710 · The Johnson-Cook (JC) constitutive model was utilized to simulate the processing of Al-Si piston alloy ZL109 to obtain the optimal finishing parameters in polycrystalline diamond (PCD) tool, and studied the machining quality of ordinary-turning under the optimized cutting parameters. PCD is brittle, so it is difficult to manufacture
contact2020826 · . ： JIS ISO GB YB HB ГOCT ASTM UNS ANSI AA SAE BS BS/L NF AIRLA DIN ZL101 ZL11 HZL101 AЛ9，AЛ9B A03560 A13560 356.0 A356.0 323 A-S7G AS7G03 GAlSi7Mg (3.2371.61... :YB－，HB－、。.
contactThe step-by-step feed cutting is put forward and adopted to machine ZL109 aluminum-silicon piston alloy. In addition, the forward and reverse finish cutting is also proposed to improve the ...
contact2017725 · A set of optimized process parameters for preparing micro arc oxidation wear resistant ceramic coating on ZL109 aluminium alloy surface is obtained, which the sodium silicate, potassium hydroxide ...
contact202327 · [18] ZHOU Y, SUN H, LI A, et al. FEM Simulation-based Cutting Parameters Optimization in Machining Aluminum-silicon Piston Alloy ZL109 with PCD Tool[J]. Journal of Mechanical Science and Technology, 2019, 33(7):3457-3465.
contact2011113 · 1、ZL101、ZL102、ZL107Al-Si 2、ZL101Al-SI-Mg、ZL102Al-Si、ZL107Al-Si-Cu$ c2 H- H7 n7 | 3、，，ZL107
contact2023324 · Anodizing is a widely used method for increasing the wear and corrosion resistance of aluminum alloys. However, it is known that the porous brittle al…
contact