E-mail: [email protected]
2022811 · The 7B52 laminated (7A52/7A01/7A62 layers) aluminum alloy is a novel and promising material used for light armor, while the nonuniform deformation behavior
contact2022811 · The 7B52 laminated (7A52/7A01/7A62 layers) aluminum alloy is a novel and promising material used for light armor, while the nonuniform deformation behavior
contact201911 · Introduction 7A52 is a heat treatable Al-Zn-Mg alloy which is widely used in light armored vehicle body due to its light weight, good corrosion resistance, high
contact201881 · Damage tolerance improvement in the lamination of aluminum alloy plates and composites has been reported in many studies. In the present study the macro-micro dynamic deformation behavior and related mechanisms of 7A52/7A01/7B52 laminated plates processed by hot roll bonding of 7A52, 7A01 and 7B52 plate at high strain rates
contact2022811 · Due to its low density, high tensile strength and excellent energy absorption capability, 7B52 laminated (7A52/7A01/7A62 layers) aluminum alloy is a promising material for the application of armored vehicles and tanks. With the rapid development of anti-armor weapons, there is an increasing need for 7B52 laminates with
contact2019116 · A spray formed 7055 Al alloy, and traditional formed 6061 Al and 7A52 Al alloy were subjected to extrusion. Later 7055Al and 7A52 treated with T6 and 6061 Al treated with T6511 heat treatment.
contact201911 · Introduction 7A52 is a heat treatable Al-Zn-Mg alloy which is widely used in light armored vehicle body due to its light weight, good corrosion resistance, high strength and toughness, etc [1]. The plates of vehicle body are mainly jointed by welding.
contact200881 · 7A52 Al alloy plate aged at 105 °C for 8 h and then at 130 °C for 24 h was welded by means of TIG using Al-6.3Mg-0.35Sc-0.1Zr-0.1Cr solder wire.
contact2018817 · MPa,89%; 3) 150 mm/ min ,7A52 , FSW452 MPa, 89%,, 1 7A52FSW Table 1 Results oftensiletests for7A52
contact201881 · Damage tolerance improvement in the lamination of aluminum alloy plates and composites has been reported in many studies. In the present study the macro-micro dynamic deformation behavior and related mechanisms of 7A52/7A01/7B52 laminated plates processed by hot roll bonding of 7A52, 7A01 and 7B52 plate at high strain rates
contact202177 · 7A52 (Al-Zn-Mg-Cu) alloy is a high-strength aluminum alloy; its welded joints are often accompanied by defects such as poor wear resistance and low fatigue strength. Herein, we try to optimize the welded joint of 7A52 aluminum alloy by using ultrasonic impact treatment (UIT). Generally, the mechanical properties such as microhardness and fatigue
contact2022811 · 7A52 layer and 7B52 alloy were 771 MPa, 503 MPa and 573 MPa, respectively. This indicated that the impact resistance of the 7B52 laminated aluminum alloy was approximately the average value of the 7A62 and 7A52 layers. Furthermore, the impact strains of the 7A62 layer, 7A52 layer and 7B52 alloy were 0.257, 0.280 and 0.257,
contact2019116 · A spray formed 7055 Al alloy, and traditional formed 6061 Al and 7A52 Al alloy were subjected to extrusion. Later 7055Al and 7A52 treated with T6 and 6061 Al treated with T6511 heat treatment. To investigate the microstructure evolution by optical microscopy (OM), scanning electron microscopy (SEM), electron back scattering
contact201911 · Introduction 7A52 is a heat treatable Al-Zn-Mg alloy which is widely used in light armored vehicle body due to its light weight, good corrosion resistance, high strength and toughness, etc [1]. The plates of vehicle body are mainly jointed by welding. Laser welding is a promising technology to weld 7A52 aluminum alloy because of the low heat ...
contact200881 · 7A52 Al alloy plate aged at 105 °C for 8 h and then at 130 °C for 24 h was welded by means of TIG using Al-6.3Mg-0.35Sc-0.1Zr-0.1Cr solder wire.
contactThe Forming and Its Prevention of Compounds in 7A52 Aluminum Alloy 7A52Mn,,,7A52 ...
contact201881 · Damage tolerance improvement in the lamination of aluminum alloy plates and composites has been reported in many studies. In the present study the macro-micro dynamic deformation behavior and related mechanisms of 7A52/7A01/7B52 laminated plates processed by hot roll bonding of 7A52, 7A01 and 7B52 plate at high strain rates
contact202177 · 7A52 (Al-Zn-Mg-Cu) alloy is a high-strength aluminum alloy; its welded joints are often accompanied by defects such as poor wear resistance and low fatigue strength. Herein, we try to optimize the welded joint of 7A52 aluminum alloy by using ultrasonic impact treatment (UIT).
contact2022811 · 7A52 layer and 7B52 alloy were 771 MPa, 503 MPa and 573 MPa, respectively. This indicated that the impact resistance of the 7B52 laminated aluminum alloy was approximately the average value of the 7A62 and 7A52 layers. Furthermore, the impact strains of the 7A62 layer, 7A52 layer and 7B52 alloy were 0.257, 0.280 and 0.257,
contact201911 · Introduction 7A52 is a heat treatable Al-Zn-Mg alloy which is widely used in light armored vehicle body due to its light weight, good corrosion resistance, high strength and toughness, etc [1]. The plates of vehicle body are mainly jointed by welding.
contact200881 · 7A52 Al alloy plate aged at 105 °C for 8 h and then at 130 °C for 24 h was welded by means of TIG using Al-6.3Mg-0.35Sc-0.1Zr-0.1Cr solder wire.
contact201875 · -analysis of tube bending forming technology.docx,IVIV I II HYPERLINK \l "_bookmark0" 1 1 HYPERLINK \l "_bookmark1" 1.1 1 HYPERLINK ...
contact