198181 · Abstract. Copper Alloy No. C93700 is a cast bronze with relatively low strength, good machinability and good corrosion resistance. Commercial names formerly used (not recommended) are (1) High-Leaded Tin Bronze, (2) Ingot No. 305, (3) Bushing and Bearing Bronze and (4) 80-10-10. Its many applications include bearings, bushings,
contactC93700 SAE 64 is a Leaded Tin Bronze. It is sometimes referred to as 80-10-10 Bronze. This references the chemical composition of 80 % Copper, 10 % Tin, and 10% Lead.
contactc93700 spec sheet concast line card C93700 Product Description: High-Leaded Tin Bronze Solids: 1/2" to 10" O.D. Tubes: 1" to 16" O.D. Rectangles: Up to 20" Standard Lengths:
contact2022811 · C93700 (SAE64),LBC3、、。. C93700 (SAE64):. C93700 (SAE64):、,。. ,,、、60MPa ...
contact2017731 · . · TA1289. . astm b584 . ASTM B584 Standard Specification for Copper Alloy Sand Castings for General Applications. . :ASTM(American Society for Testing and Materials,ASTM)。. ...
contactThermal Conductivity Btu/ sq ft/ ft hr/ °F at 68°F. 27.1. Coefficient of Thermal Expansion 68-392 10 to -6 power per °F (68 – 392°F) 10.3. Specific Heat Capacity Btu/ lb /°F at 68°F. 0.09. Modulus of Elasticity in Tension ksi. 11000. Incipient Melting °F.
contact20221029 · : C93700 : : : :C93800 :C93500 /% Cu Sn Al Fe Mn Ni Pb Si P Zn 78.0-82.0 9.0-11.0 0.01 0.7-0.5 8.0-11.0 ...
contact2022811 · C93700 (SAE64),LBC3、、。. C93700 (SAE64):. C93700 (SAE64):、,。. ,,、、60MPa ...
contact2022615 · Our RO4000 series material are available laminated with LoPro copper foil. Crystalline Structure Electrodeposited copper crystals tend to grow lengthwise in the Z-axis of the foil. Typically, a polished cross-section of electrodeposited copper foil has the appearance of a picket fence, with long crystal boundaries perpendicular to the foil plane.
contact202332 · 、PCB ()35um (1.4mil),50um70um。. 35um=1oz (1.4mil),17.5um (0.7mil)。. 70%35um,PCB、;,PCB, ...
contactC93700 SAE 64 Bearing Bronze is a good general bearing material. Alloy C937 is known for it's corrosion resistance to mildly acidic mine waters and paper mill sulfite. The addition of lead to this alloy makes it easy to
contact202111 · The effect of volume ratios of liquid Babbitt/solid Cu (V L /V S) on the interfacial structure of Babbitt- C93700 Cu bimetallic composites were evaluated.Compound casting process was used for bimetallic composites fabrication. In current research work, Sn-based Babbitt alloy was melted in an electrical furnace and was poured at 420 °C onto
contactIntroduction. High-leaded tin bronze UNS C93700 copper casting alloy is an alloy of copper-tin-lead. The addition of nickel in the alloy enhances the strength and ductility. UNS C93700 copper alloy is resistant to biofouling and corrosion. The following datasheet provides the chemical composition and properties of UNS C93700 alloy.
contact202111 · C93700 Leaded tin bronze alloy was prepared according to the standard composition [12] as mentioned in Table 1 and sand casted into rods of length 200 mm and diameter 15 mm. These rods were machined into ASTM standard test specimens for tensile, hardness and wear tests. Five specimens were allotted for each test in which one is a
contact2022106 · :. C3604(JIS),GBH59-3 () . . . . . . GB.
contact