E-mail: [email protected]
355.0 Aluminum Silicon Copper; C355.0 Aluminum Silicon Copper; 356.0 Aluminum Silicon Magnesium; A356.0 Aluminum Silicon Magnesium; A357.0 Aluminum Silicon
contact2020530 · A356.0-F aluminum is A356.0 aluminum in the as-fabricated (no temper or treatment) condition. It has the lowest strength compared to the other variants of A356.0
contact2020530 · A356.0 aluminum is an aluminum alloy formulated for casting. A356.0 is the Aluminum Association (AA) designation for this material. A13560 is the UNS number.
contact2023322 · （）（Tensile Strength, Yield）：≥165 MPa (@Strain 0.200%) （）（Tensile Modulus）：72.4 GPa （Elongation
contactA356.0 is the designation for this material from Aluminum Association (AA). In UNS standard, it is A13560 and the SAE designation is 336. A356 aluminum die casting alloy has good casting and machining
contact2020530 · A356.0 aluminum is an aluminum alloy formulated for casting. A356.0 is the Aluminum Association (AA) designation for this material. A13560 is the UNS number. Additionally, the SAE designation is 336. And the AFNOR (French) designation is A-S7G. Older literature may refer to this material as SG70B, but this is now discouraged.
contactA356.0 Aluminum Applications Adapter Base Air Horn Elbow Aircraft Fittings Airframe Castings Anchor Base Automobile Wheels Base Base Cover Base With Hole Blower Body Bollard Base Bracket Bracket Accelerator Breech Ring Bridge Wedge Cage Clamp Clamp Ball Coupler Crank Case Door Door Frame Door Frame Section Electric Motor Parts End
contactThe A356 aluminum alloy is a composition of 92.05% Aluminum, 7% Silicon, 0.2% iron, 0.35% Magnesium, 0.2% Copper, Manganese and Zinc are 0.1% each. The parent metal of this alloy is aluminum since it makes up 92% of the material. Since the alloy has excellent machining and casting properties it is used in heat treatment procedures of T5 and T6.
contact2018319 · A356.0 ALUMINIUM CASTING ALLOY (7Si-0.3Mg) Mass Characteristics Density. 2.685 g/cm_ (0.097 lb/in_) at 20ºC (68ºF) Thermal Properties Liquidus temperature. 615ºC (1135ºF) Solidus temperature. 555ºC (1035ºF) Coefficient of linear thermal expansion. Temperature range Average coefficient
contact20201117 · ()ADC12、A356、ZL102ZL104 ADC12 ZLD102 ZLD104 A356 ZAlSi12 ZAlSi9Mg ZL102 ZL104 （%）
contact2018319 · A356.0 ALUMINIUM CASTING ALLOY (7Si-0.3Mg) Mass Characteristics Density. 2.685 g/cm_ (0.097 lb/in_) at 20ºC (68ºF) Thermal Properties Liquidus temperature. 615ºC (1135ºF) Solidus temperature. 555ºC (1035ºF) Coefficient of linear thermal expansion. Temperature range Average coefficient
contact2021622 · Fig. 2 shows the microstructures of as-cast A356 alloy and A356/Ti composite containing 0.5, 1.5, 5 wt% Ti. As seen, the microstructure of A356 alloy (Fig. 2 (a) and (b)) includes aluminum-rich dendrites and eutectic silicon.The eutectic silicon phase in the as-cast A356 alloy is typically coarse and needle-shaped, as shown in Fig. 2 (b).
contactConsult the appropriate specification from an accredited specifying body (ASTM, SAE, Federal or Military) to determine current minimum values of this alloy. 3. Use appropriate design safety factors. 4. Use Failure Modes and Effects Analysis to help identify possible weaknesses in designs and specifications. 5.
contact（ASTM）A356，ZL101A、AC4CH、AlSi7Mg、A-S7G03、Aл9-1。 A356，AlSi9Mg、AlSi10Mg、AlSi11Mg，A-S11G、A-S12.5。 Si，、、、。
contact2020530 · A356.0 aluminum is an aluminum alloy formulated for casting. A356.0 is the Aluminum Association (AA) designation for this material. A13560 is the UNS number. Additionally, the SAE designation is 336. And the AFNOR (French) designation is A-S7G. Older literature may refer to this material as SG70B, but this is now discouraged.
contact2023322 · Ultimate）：≥234 MPa （）（Tensile Strength, Yield）：≥165 MPa (@Strain 0.200%) （）（Tensile Mod Failed to fetch / Aluminum A356.0-T6, Sand Cast -RAN ...
contact